TIA/EIA structured cabling standards


TIA/EIA structured cabling standards
   Standards specified by the Electronics Industry Association/Telecommunications Industries Association (EIA/TIA), including:
   • ANSI/EIA/TIA-568-1991 Commercial Building Telecommunications Wiring.
   • EIA/TIA TSB-36 Additional Cable Specifications for UTP Cables. 1991.
   • EIA/TIA TSB-40 Telecommunications Systems Bulletin—Additional Transmission Specifications for UTP Connecting Hardware. 1992.
   • ANSI/EIA/TIA-568A 1995 revises the original 568 document and adds material from TSB-36 and TSB-40.
   • ANSI/EIA/TIA-569-1990 Commercial Building Standard for Telecommunications Pathways and Spaces.
   • ANSI/EIA/TIA-570-1991 Residential and Light Commercial Telecommunications Wiring Standard.
   • ANSI/EIA/TIA-606-1993Administration Standard for the Telecommunications Infrastructure of Commercial Buildings.
   • ANSI/EIA/TIA-607-1994 Commercial Building Grounding and Bonding Requirements for Telecommunications.
   Local codes and standards may impose additional requirements.
   See also cabling standards.

Dictionary of networking . 2014.

Look at other dictionaries:

  • TIA/EIA-568-B — is a set of three telecommunications standards from the Telecommunications Industry Association, a 1988 offshoot of the EIA. The standards address commercial building cabling for telecom products and services. The three standards are formally… …   Wikipedia

  • Structured cabling — Data center. Structured cabling is building or campus telecommunications cabling infrastructure that consists of a number of standardized smaller elements (hence structured) called subsystems. Structured cabling falls into six subsystems:[1][2] …   Wikipedia

  • TIA 570B — is a cabling standard for residential telecommunications.TIA 570B supersedes the TIA 568A for residential standards. Telecommunications Industry Association (TIA) publishes TIA 570 B Residential Telecommunications Infrastructure Standard, which… …   Wikipedia

  • Modular connector — This article is about modular connectors. For the registered jack (RJ) wiring standard, see registered jack. Left to right, modular connectors: 8P8C plug, 6P6C plug, 6P4C plug, 4P4C plug, 6P6C jack …   Wikipedia

  • 8P8C — The 8 Position 8 Contact (8P8C) modular plugs and sockets are communications connectors. Under the same naming scheme, an 8P6C connector has eight positions, with six positions containing conductors, and a 6P6C connector has six positions, all… …   Wikipedia

  • Fiber to the x — (FTTX) is a generic term for any network architecture that uses optical fiber to replace all or part of the usual copper local loop used for telecommunications. The four technologies, in order of an increasingly longer fiber loop are:* Fiber to… …   Wikipedia

  • ISO/IEC 11801 — International standard ISO/IEC 11801 specifies general purpose telecommunication cabling systems (structured cabling) that are suitable for a wide range of applications (analog and ISDN telephony, various data communication standards, building… …   Wikipedia

  • Category 3 cable — Category 3 cable, commonly known as Cat 3, is an unshielded twisted pair (UTP) cable designed to reliably carry data up to 10 Mbit/s, with a possible bandwidth of 16 MHz. It is part of a family of copper cabling standards defined jointly by the… …   Wikipedia

  • Crossover cable — This article is about crossover cables in general. For Ethernet crossover cables, see Ethernet crossover cable. A crossover cable connects two devices of the same type, for example DTE DTE or DCE DCE, usually connected asymmetrically (DTE DCE),… …   Wikipedia


Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”

We are using cookies for the best presentation of our site. Continuing to use this site, you agree with this.